| A |
|
| Abrasion |
The wearing away of a surface by rubbing or scraping. |
| Absorption |
The penetration into one material by another. |
| Acetone |
A flammable solvent with a low health hazard, used to thin and clean up uncured epoxy resins. It's usefulness for cleanup is limited by its rapid evaporation rate. |
| Adherent |
A material which is held to another material by an adhesive. |
| Ambient |
Existing environmental conditions, including temperature, pressure and humidity. |
| Amine Blush |
A sticky or greasy film which forms on the top of some amine- or polyamide-cured epoxy resins. It is removable by scrubbing with soap and water. |
| Amine Carbamate |
The chemical nomenclature for amine blush (see above). |
| Aqueous |
Solutions or mixtures containing water. |
| |
|
| B |
|
| B Staged |
Epoxy resin which is cured enough to be hard and brittle, with little or no strength, is said to be "B Staged." |
| Bag molding |
A technique in which fluid pressure is applied to a plastic in a mold through a flexible membrane. |
| Bubble |
A spherical void trapped within a plastic material, created by trapped air. |
| |
|
| C |
|
| Carvel Planking |
A traditional style of wooden boat construction in which the wood strips, or planks, for the hull are placed with a gap between them on purpose, so that a swellable caulking material can be applied later which will make the boat watertight. |
| Cast |
To form a plastic material into a desired shape by pouring it into a mold. |
| Chalking |
Some polymer films gradually degrade from ultraviolet light exposure (sunlight). One sign of that degradation is formation of powder on the surface of the film. This process is called "chalking." |
| Cohesion |
The force holding a substance together. |
| Composite |
A material matrix consisting of a thermosetting polymer resin and a reinforcing fabric. The fabric provides the strength and the resin distributes the load and provides dimensional stiffness. |
| Compressive Strength |
The ability of a material to resist a crushing force. |
| Cross Laminate |
A laminate in which some of the layers, with regard to the strongest direction, are laid up at right angles to others. |
| Cure |
The process of hardening of a catalyzed resin. |
| Curing Agent |
A chemical that causes a resin to cure; a hardening agent. |
| |
|
| D |
|
| Debonding |
An adhesive failure between two surfaces glued together, typically occurring between layers of laminating resin or between a coating and a substrate. |
| Delamination |
A split in a laminated plastic along the plane of its layers. |
| Diluent |
A liquid added to a plastic resin to lower the viscosity of the resin. |
| Dimensional Stability |
The ability of a resin system to retain precise size and shape after cure. |
| |
|
| E |
|
| Elongation |
The increase in length of a material under tension. |
| Epoxy Resin |
A thermosetting resin used in tooling applications. |
| Exotherm |
Chemical reaction producing heat. |
| |
|
| F |
|
| Fiber Pattern |
The thread size and weave of fiberglass cloth. |
| Flash Point |
The temperature at which a flammable material ignites. |
| Flexible Molds |
Molds which can be stretched to remove cured plastics. |
| Flexural Strength |
The strength of a material in bending. |
| |
|
| G |
|
| Gel |
A semi-solid state in a liquid resin. |
| Gel Time |
The amount of time required for the mixed hardener and resin to gel. |
| |
|
| H |
|
| Hardener |
A reactive chemical which causes a resin to cure; a curing agent. |
| Heat Distortion Point |
The temperature at which a test bar deflects under a given flexural load and a prescribed amount of heat. |
| |
|
| I |
|
| Impregnate |
To saturate reinforcement with plastic. |
| Inert |
Chemically inactive. |
| |
|
| L |
|
| Laminate |
To join sheets or layers of a material with a bonding agent, such as using epoxy resins to bond layers of fiberglass cloth. |
| Lay-up |
The positioning of reinforcing material and a plastic in a mold or over a model. |
| |
|
| M |
|
| Mil |
0.001 inch. |
| Mold |
The cavity or matrix containing a plastic. |
| Mold Release |
An agent used to prevent a plastic from sticking to the mold. |
| |
|
| P |
|
| Parallel Laminate |
A laminate in which all layers of the reinforcement are aligned parallel to the strongest direction in tension. |
| Plasticity |
That property of plastics which permits them to be permanently shaped without breaking when sufficient shaping force is applied. |
| Polyesters |
Thermosetting plastics of the type used in fiberglass boat hull and automobile body construction. |
| Polyurethane |
Thermosetting plastic used for foam insulation, flexible molds, protective coatings, and abrasion resistant castings. |
| Porous Mold |
A mold made of bonded or fused particles of various sizes, which, when completed, will permit the passage of air or liquids through the mass. |
| Post Cure |
A process employed after the initial cure, in which a plastic is given a final oven cure to achieve optimum physical properties. |
| Pot Life |
The amount of time in which resin and hardener can be used after mixing. |
| |
|
| R |
|
| Reinforcement |
Material used to strengthen a plastic, such as fiberglass. |
| Resin |
Liquid, semi-solid organic material occurring naturally or produced synthetically. With respect to plastics a resin is the primary material which is polymerized (cured) to a useful plastic product. |
| Room Temperature |
77ºF |
| |
|
| S |
|
| Safety Hardener |
A curing agent having minimum toxic effects on the human body. |
| Solvent |
A type of liquid used to dissolve another material. |
| Spline |
To prepare a surface to desired contours by working a paste material. |
| Spray-up |
A technique employing a spray gun to prepare a reinforced plastic article. |
| Substrate |
Any surface on which an adhesive or coating is spread. |
| Sweat-out |
The formation of a liquid on the surface of a cured plastic; exudation. |
| |
|
| T |
|
| Tack |
Stickiness. |
| Tensile Strength |
The strength of a material in tension. |
| Thermal Conductivity |
The ability of a material to conduct heat. |
| Thermoforming |
Shaping a plastic by heating it to its softening point and cooling it on a mold. |
| Thermoplastic |
A plastic which is capable of being re-formed a number of times by heating. |
| Thermosetting Resin |
A plastic which cures through chemical reaction to an essentially infusible material. Thermosetting resins cannot be re-formed after final cure. (Refer to "Epoxy Resins") |
| Thixotropic |
A property of materials which are quite thick while standing and become thinner when agitated. |
| |
|
| U |
|
| Undercure |
The condition of a molded article which results when not enough time or temperature has been applied to bring about final cure and achieve maximum physical properties. |
| |
|
| V |
|
| Viscosity |
Thickness. |
| Voids |
Air pockets trapped within a material, such as a plastic-fiberglass laminate. |
| |
|
| W |
|
| Working Life |
The period of time after mixing a resin and hardener in which the material remains a liquid. Varies with type of plastic, amount of mixed material, and ambient temperature. |
| |
|
| |
|